Push up and turn the bottom of the Super Pump to the right until it is tight. Turn on water. When water fills hose and runs into mattress, turn the Super Pump’s bell to the left and pull down (F). After 1-3 minutes of draining, reduce flow from faucet by two-thirds.
How do you drain a waterbed with a drain kit?
Waterbed Drain Kit – Draining Your Waterbed FAQs Remove the faucet aerator and attach the faucet adapter to a sink. Next, attach the Venturi Pump to the faucet adapter. Turn the bell-shaped bottom piece of the Venturi Pump to the marked drain position.
How do you drain water out of a waterbed?
How Do You Drain a Waterbed?
- Unplug the heater before draining the waterbed for your safety.
- Put a towel by the valve and burp all the air out of the mattress.
- Burp out the air again!
- Put the cap back on the mattress to keep air from going in.
- Put the hose extension on the end of the hose.
How long does it take to drain a waterbed with a pump?
A pump can speed the process up, especially if the drain hose isn’t getting much help from gravity. With a pump, a king-size waterbed takes just under an hour to drain, usually around 50 minutes.
How do I know when my waterbed is full?
When the water nears the bottom of the straight edge the fill will be complete. The mattress will need to be shut off for people of average weight and size about ½ inch below the guide. Touching the guide in the middle is too full. ¾ of an inch or so seems to be best for people who are in excess of 200 pounds.
How does a water bed work?
What Exactly Is a Waterbed? A waterbed is a vinyl mattress that is filled with water. In the peak of their popularity in the 1980s, consumers had to fill the entire waterbed with a garden hose. Now, you only have to fill tubes, called “bladders.” This makes the process less of a hassle.
How do you empty a waterbed mattress without a pump?
How to Drain a Waterbed Without a Pump
- Unplug the temperature control unit, if you waterbed has one.
- Attach one end of a garden hose to a faucet outside the house and the other end to the waterbed’s drain valve.
- Turn on the water for 15 seconds.
- Turn off the water and disconnect the hose from the faucet.
How do you use a magic pump?
Lay clean bath towels around the fill valve to absorb any water overflow during air extraction. Unscrew and remove the waterbed valve cap. Screw the Blue Magic Super Pump air extractor to the waterbed valve. Grip the handle of the pump and slide it out and away then back towards the waterbed valve.
How do you drain a land and sky waterbed?
The best and easiest way to drain the bed is to obtain a small electric draining pump (utility water pump can be rented from Home Depot), or, insert your garden hose with waterbed hose connector into the “popped-up” valve.
Can you fill a waterbed with hot water?
After connecting hose and fill kit connections you can begin to fill the bed but never fill with straight hot water. Cold or lukewarm is fine. Throughout the beginning fill process continue to pull corners of mattress into the corners of the mattress bed cavity.
Do waterbeds lose water?
A waterbed does this naturally when properly filled and offers the best support for your back. Water, H2O, contains Hydrogen and Oxygen, the heater evaporates the water, creating air bubbles. Therefore, it is important that you add 20 – 25 litres of water back into the bladder each 12 months.
How do I use the Blue Magic Fill and drain kit?
Connect hose to Super Pump. F. Turn Super Pump’s bell to the left and pull down. Filling and/or draining your softside or hardside waterbed is easier than ever when you use the Blue Magic Fill and Drain Kit. Everything you need is included, making your task much easier.
How do you use Blue Magic Bubble stop on a mattress?
Fill mattress with warm, not hot, water until you reach the desired fill level. Remove hose. Add one 8 oz. bottle Blue Magic® Waterbed Conditioner and one 8 oz. Bottle Blue Magic® Bubble Stop (if necessary) following directions on bottles. Unscrew Perfect Union® and replace Pull-Cap®.
How do you fill a perfect union mattress with water?
Pull up on Pull-Cap tabs to extend the valve and remove Pull-Cap (C). Connect Perfect Union® to the hose, then connect to mattress valve (D). Fill mattress with warm, not hot, water until you reach the desired fill level. Remove hose.
What do I need to know before buying a waterbed?
Everything you need is included, making your task much easier. Be sure to unplug your waterbed heater prior to filling or draining your waterbed. Always use a clean, uncontaminated hose to prevent unwanted bacteria from entering your bed through a dirty hose.
